| Highlights |
- Supports PCI Express Specification Revision 1.1
- Single (x1) PCI Express Lane, Low-Profile Form Factor
- 10/100/1000M Gigabit Ethernet (POE+) ports
- Support IEEE 802.3at for PoE+ (Power over Ethernet Plus)
- Power Sourcing Equipment (PSE) design, provides data and up to 30W of power on ethernet port
- Supports jumbo frame to 9K bytes
|
| Introduction |
|
The GEP-PCIE1XG101 is 1-port 10/100/1000M Ethernet (POE+) to PCI Express x1 Host Card.
The 10/100/1000M Ethernet controller supports the PCI Express 1.1 bus interface for host communications with power management, and is compliant with the IEEE 802.3u specification for 10/100Mbps Ethernet and the IEEE 802.3ab specification for 1000Mbps Ethernet.
The 10/100/1000M Ethernet controller is fully compliant with Microsoft NDIS5, NDIS6 (IPv4, IPv6, TCP, UDP) Checksum and Segmentation Task-offload (Large send and Giant send) features, and supports IEEE 802 IP Layer 2 priority encoding and IEEE 802.1Q Virtual bridged Local Area Network (VLAN). The above features contribute to lowering CPU utilization, especially benefiting performance when in operation on a network server.
|
| Technical Specifications |
| Ethernet Feature |
- Integrated 10/100/1000M transceiver
- Auto-Negotiation with Next Page capability
- Supports PCI Express 1.1
- Supports pair swap/polarity/skew correction
- Crossover Detection & Auto-Correction
- Wake-on-LAN and remote wake-up support
- Microsoft NDIS5, NDIS6 Checksum Offload (IPv4, IPv6, TCP, UDP) and Segmentation Task-offload (Large send v1 and Large send v2) support
- Supports Full Duplex flow control (IEEE 802.3x)
- Supports jumbo frame to 9K bytes
- Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
- Supports IEEE 802.1P Layer 2 Priority Encoding
- Supports IEEE 802.1Q VLAN tagging
- Supports IEEE 802.3az-2010 (EEE)
- Supports power down/link down power saving
- Supports PCI MSI (Message Signaled Interrupt) and MSI-X
- Supports quad core Receive-Side Scaling (RSS)
- Supports Alert Standard Format 2.0 (ASF2.0)
- Supports Protocol Offload (ARP & NS)
- Supports Customized LEDs
- Supports 1-Lane 2.5Gbps PCI Express Bus
- Supports hardware ECC (Error Correction Code) function
- Supports hardware CRC (Cyclic Redundancy Check) function
|
| POE+ Feature |
- Supports IEEE 802.3at Power Sourcing Equipment (PSE)
- Operates from a 54 V supply
- Provides PD real-time protection through the following mechanisms: overload, under-load, over-voltage, over-temperature, and short-circuit.
- Auto mode – allows turning PDs on and off automatically.
|
|
Power Input for POE
|
Step-Up 12V from either PCIe Slot or auxiliary SATA power connector
- From PCIe Slot
- 25 W Slot (Max. 25W)
- 75 W Slot (Max. 30W)
- From SATA Power Connector
|
| LED Indicators |
- Power LED
- On: Port Power On (normal operation)
- 0.4Hz Blink: Power Management event
- 0.8Hz Blink: Port Over Load / Port Short Circuit / Port failed at Startup
- 3.3Hz Blink: Vmain_Out of Range or Over Temp
- Off: Port Off
- Link Status LED
|
| Number of Port: |
- 10/100/1000M Gigabit Ethernet (POE+) port
- 1000 BASE-T Single-Port Magnetics/RJ-45 with POE
|
|
| Computer Platform |
- Computer with PCI Express slot ( x1, x4, x8, x16)
|
| Operating System Requirements |
- Windows XP/ Vista/ 7/ 8/ 10
- Linux kernel 3.x /2.6.x/ 2.4.x
|
| Physical Dimensions |
- 64mm(H) x 118mm(L)
- NW: 73.5g
|
| Optional Accessories |
- Low Profile PCI Bracket (BR-00194-30-1020)
Specifications subject to change without prior notice
|
|
